Stormy water on Mars: The distribution and saturation of atmospheric water during the dusty season.

The loss of water from Mars to space is thought to result from the transport of water to the upper atmosphere, where it is dissociated to hydrogen and escapes the planet. Recent observations have suggested large, rapid seasonal intrusions of water into the upper atmosphere, boosting the hydrogen abundance. We use the Atmospheric Chemistry Suite on the ExoMars Trace Gas Orbiter to characterize the water distribution by altitude. Water profiles during the 2018-2019 southern spring and summer stormy seasons show that high-altitude water is preferentially supplied close to perihelion, and supersaturation occurs even when clouds are present. This implies that the potential for water to escape from Mars is higher than previously thought.

Gold nanoparticle printed coverslips to facilitate fluorescence-TEM correlative microscopy.

Correlative light and electron microscopy (CLEM) allows combining the advantages of fluorescence microscopy and electron microscopy for cell imaging. Rare phenomenon expressing cells can be studied by specifically tagged fluorophores with fluorescence microscopy. Subsequently, cells can be fixed and ultra-structural details can be studied with transmission electron microscopy (TEM) at a higher resolution. However, precise landmarks are necessary to track the same cell throughout the CLEM process. In this technical report, we present a high contrast inkjet-printed gold nanoparticle patterns over commercial glass coverslip to facilitate cell tracking with correlative microscopy. High contrast and strong reflection from nano gold pattern can be used as a fixed landmark for cell identification with fluorescence microscopy. Nano gold printed letters over coverslips are visible in resin blocks, which can be further used to identify the cell of interest for performing sectioning of embedded cell blocks for TEM.

Photothermal effect of gold nanostar patterns inkjet-printed on coated paper substrates with different permeability.

Inkjet printing of spherical gold nanoparticles is widely applied in the fabrication of analytical and diagnostics tools. These methods could be extended to non-spherical gold nanoparticles that can efficiently release heat locally when irradiated in the near infrared (NIR) wavelength region, due to localized surface plasmon resonance (LSPR). However, this promising application requires the ability to maintain high efficiency and tunability of the NIR LSPR of the printed nanoparticles. In this study stable inks containing PEGylated gold nanostars (GNS) were fabricated and successfully inkjet-printed onto differently coated paper substrates with different porosity and permeability. A pronounced photothermal effect was observed under NIR excitation of LSPR of the printed GNS patterns even at low laser intensities. It was found that beside the direct role of the laser intensity, this effect depends appreciably on the printing parameters, such as drop density (δ, drops/mm2) and number of printed layers, and, critically, on the permeability of the coated paper substrates. These results will promote the development of GNS-based printed platforms for local photothermal therapy.

Fabrication of Inkjet-Printed Gold Nanostar Patterns with Photothermal Properties on Paper Substrate.

Inkjet printing technology has brought significant advances in patterning various functional materials that can meet important challenges in personalized medical treatments. Indeed, patterning of photothermal active anisotropic gold nanoparticles is particularly promising for the development of low-cost tools for localized photothermal therapy. In the present work, stable inks containing PEGylated gold nanostars (GNSs) were prepared and inkjet printed on a pigment-coated paper substrate. A significant photothermal effect (ΔT ≅ 20 °C) of the printed patterns was observed under near infrared (NIR) excitation of the localized surface plasmon resonance (LSPR) of the GNS with low laser intensity (I ≅ 0.2 W/cm(2)). Besides the pronounced photothermal effect, we also demonstrated, as an additional valuable effect, the release of a model fluorescent thiol-terminated Bodipy dye (BDP-SH) from the printed gold surface, both under bulk heating and NIR irradiation. These preliminary results suggest the way of the development of a new class of low-cost, disposable, and smart devices for localized thermal treatments combined with temperature-triggered drug release.

Protein and bacterial interactions with nanostructured polymer coatings.

Adsorption of proteins and adhesion of bacteria to a surface is affected by chemical and physical interactions. In this study, polymer coatings and their ability to adsorb avidin and Staphylococcus aureus were investigated. The surface chemistry and topography of the polymer coatings was modified by changing the weight ratio of the hydrophobic polystyrene (PS) and the hydrophilic acrylonitrile butadiene styrene (ABS) components in the polymer blend. Avidin adsorbed less to the ABS phase compared with the PS phase. The side-on orientation of avidin on the ABS surface, however, resulted in a higher specific binding of biotinylated bovine serum albumin. Steric effects and hydrophobic protein-surface interactions decreased the activity of avidin on the PS phase. The increased hydrophobicity and roughness of the polymer coatings enhanced the adhesion of S. aureus. The avidin-coated latex surface with 55% relative surface coverage of the PS phase showed anti-microbial behavior.

Cellulose nanocrystals prepared via formic acid hydrolysis followed by TEMPO-mediated oxidation.

Cellulose nanocrystals (CNCs) as a renewable and biodegradable nanomaterial have wide application value. In this work, CNCs were extracted from bleached chemical pulp using two stages of isolation (i.e. formic acid (FA) hydrolysis and 2,2,6,6-tetramethyl-piperidine-1-oxyl (TEMPO) mediated oxidation) under mild conditions. In the first stage, FA was used to remove hemicellulose, swell cellulose fibers, and release CNCs. The FA could be readily recovered and reused. In the second stage, the CNCs isolated by FA were further modified by TEMPO-mediated oxidation to increase the surface charge of CNCs. It was found that the modified CNCs with more ordered crystal structure and higher surface charge had better redispersibility and higher viscosity in aqueous phase. Therefore, the modified CNCs could be more effective when used as rheology modifier in the fields of water based coating, paint, food etc.

Improvement of dissolution rate of indomethacin by inkjet printing.

The aim of this study was to prepare printable inks of the poorly water soluble drug indomethacin (IMC), fabricate printed systems with flexible doses and investigate the effect of ink excipients on the printability, dissolution rate and the solid state properties of the drug. A piezoelectric inkjet printer was used to print 1×1cm(2) squares onto a paper substrate and an impermeable transparency film. l-arginine (ARG) and polyvinylpyrrolidone (PVP) were used as additional formulation excipients. Accurately dosed samples were generated as a result of the ink and droplet formation optimization. Increased dissolution rate was obtained for all formulations. The formulation with IMC and ARG printed on transparency film resulted in a co-amorphous system. The solid state characteristics of the printed drug on porous paper substrates were not possible to determine due to strong interference from the spectra of the carrier substrate. Yet, the samples retained their yellow color after 6months of storage at room temperature and after drying at elevated temperature in a vacuum oven. This suggests that the samples remained either in a dissolved or an amorphous form. Based on the results from this study a formulation guidance for inkjet printing of poorly soluble drugs is also proposed.

Printing technologies for biomolecule and cell-based applications.

Biomolecules, such as enzymes, proteins and other biomacromolecules (polynucleotides, polypeptides, polysaccharides and DNA) that are immobilized on solid surfaces are relevant to many areas of science and technology. These functionalized surfaces have applications in biosensors, chromatography, diagnostic immunoassays, cell culturing, DNA microarrays and other analytical techniques. Printing technologies offer opportunities in this context. The main interests in printing biomolecules are in immobilizing them on surfaces for sensors and catalysts or for controlled delivery of protein-based drugs. Recently, there have been significant developments in the use of inkjet printing for dispensing of proteins, biomacromolecules and cells. This review discusses the use of roll-to-roll and inkjet printing technologies in manufacturing of biomolecule and cell-based applications.

Fabrication of drug-loaded edible carrier substrates from nanosuspensions by flexographic printing.

The main goal of the current work was to investigate the possible use of flexographic printing for the conversion of nanosuspensions into solid dosage forms. Aqueous nanosuspensions of indomethacin (IND) and itraconazole (ITR) with Poloxamer 407 as the stabilizer agent were prepared by wet ball-milling. The nanosuspensions were flexographically printed on three different substrates, including two commercially available edible substrates. The printed formulations were characterized with X-ray diffractometry (XRD) and scanning electron microscopy (SEM). In addition, dissolution studies for the printed IND and ITR formulations were conducted. The mean particle size of milled nanosuspensions of IND and ITR was 422.6 ± 7.7 nm and 698.1 ± 14.0 nm, respectively. The SEM imaging showed even distribution of nanosuspensions on the substrates after printing without any evident agglomeration. The printed formulations contained drug at least partially in crystalline form. The drug dissolution rate from the prepared formulations was improved compared to the pure drug. The drug release from the preparations on edible substrates was slightly slower due to the incorporation of the drug particles into the substrate matrix. In conclusion, the results indicated that flexographic printing can be considered as a promising fabrication method of solid nanoparticulate systems with enhanced dissolution behavior.

Printed paper-based arrays as substrates for biofilm formation.

The suitability of paper-based arrays for biofilm formation studies by Staphylococcus aureus is demonstrated. Laboratory-coated papers with different physicochemical properties were used as substrates. The array platform was fabricated by patterning the coated papers with vinyl-substituted polydimethylsiloxane (PDMS) -based ink. The affinity of bacteria onto the flexographically printed hydrophobic and smooth PDMS film was very low whereas bacterial adhesion and biofilm formation occurred preferentially on the unprinted areas, i.e. in the reaction arrays. The concentration of the attached bacteria was quantified by determining the viable colony forming unit (CFU/cm(2)) numbers. The distribution and the extent of surface coverage of the biofilms were determined by atomic force microscopy. In static conditions, the highest bacterial concentration and most highly organized biofilms were observed on substrates with high polarity. On a rough paper surface with low polarity, the biofilm formation was most hindered. Biofilms were effectively removed from a polar substrate upon exposure to (+)-dehydroabietic acid, an anti-biofilm compound.

Enhanced protein adsorption and patterning on nanostructured latex-coated paper.

Specific interactions of extracellular matrix proteins with cells and their adhesion to the substrate are important for cell growth. A nanopatterned latex-coated paper substrate previously shown to be an excellent substrate for cell adhesion and 2D growth was studied for directed immobilization of proteins. The nanostructured latex surface was formed by short-wavelength IR irradiation of a two-component latex coating consisting of a hydrophilic film-forming styrene butadiene acrylonitrile copolymer and hydrophobic polystyrene particles. The hydrophobic regions of the IR-treated latex coating showed strong adhesion of bovine serum albumin (cell repelling protein), fibronectin (cell adhesive protein) and streptavidin. Opposite to the IR-treated surface, fibronectin and streptavidin had a poor affinity toward the untreated pristine latex coating. Detailed characterization of the physicochemical surface properties of the latex-coated substrates revealed that the observed differences in protein affinity were mainly due to the presence or absence of the protein repelling polar and charged surface groups. The protein adsorption was assisted by hydrophobic (dehydration) interactions.

An impedimetric study of DNA hybridization on paper-supported inkjet-printed gold electrodes.

In this study, two different supramolecular recognition architectures for impedimetric detection of DNA hybridization have been formed on disposable paper-supported inkjet-printed gold electrodes. The gold electrodes were fabricated using a gold nanoparticle based ink. The first recognition architecture consists of subsequent layers of biotinylated self-assembly monolayer (SAM), streptavidin and biotinylated DNA probe. The other recognition architecture is constructed by immobilization of thiol-functionalized DNA probe (HS-DNA) and subsequent backfill with 11-mercapto-1-undecanol (MUOH) SAM. The binding capacity and selectivity of the recognition architectures were examined by surface plasmon resonance (SPR) measurements. SPR results showed that the HS-DNA/MUOH system had a higher binding capacity for the complementary DNA target. Electrochemical impedance spectroscopy (EIS) measurements showed that the hybridization can be detected with impedimetric spectroscopy in picomol range for both systems. EIS signal indicated a good selectivity for both recognition architectures, whereas SPR showed very high unspecific binding for the HS-DNA/MUOH system. The factors affecting the impedance signal were interpreted in terms of the complexity of the supramolecular architecture. The more complex architecture acts as a less ideal capacitive sensor and the impedance signal is dominated by the resistive elements.

Staphylococcus aureus biofilm susceptibility to small and potent ß(2,2)-amino acid derivatives.

Small antimicrobial ß(2,2)-amino acid derivatives (Mw < 500 Da) are reported to display high antibacterial activity against suspended Gram-positive strains combined with low hemolytic activity. In the present study, the anti-biofilm activity of six ß(2,2)-amino acid derivatives (A1-A6) against Staphylococcus aureus (ATCC 25923) was investigated. The derivatives displayed IC50 values between 5.4 and 42.8 µM for inhibition of biofilm formation, and concentrations between 22.4 and 38.4 µM had substantial effects on preformed biofilms. The lead derivative A2 showed high killing capacity (log R), and it caused distinct ultrastructural changes in the biofilms as shown by electron and atomic force microscopy. The anti-biofilm properties of A2 was preserved under high salinity conditions. Extended screening showed also high activity of A2 against Escherichia coli (XL1 Blue) biofilms. These advantageous features together with high activity against preformed biofilms make ß(2,2)-amino acid derivatives a promising class of compounds for further development of anti-biofilm agents.

Low-cost reduced graphene oxide-based conductometric nitrogen dioxide-sensitive sensor on paper.

The fabrication concept for a low-cost sensor device using reduced graphene oxide (rGO) as the sensing material on a porous paper substrate is presented. The sensors were characterized using conductivity and capacitance measurements, atomic force microscopy and X-ray photoelectron spectroscopy. The effects of different reducing agents, graphene oxide (GO) flake size and film thickness were studied. The sensor was sensitive to NO2, and devices based on a thin (10-nm) hydrazine-reduced GO layer had the best sensitivity, reaching a 70% reduction in resistance after 10 min of exposure to 10 ppm NO2. The sensitivity was high enough for the detection of sub-parts per million levels of NO2. Desorption of gas molecules, i.e. the recovery of the sensor, could be accelerated by UV irradiation. The structure and preparation of the sensor are simple and up-scalable, allowing their fabrication in bulk quantities, and the fabrication concept can be applied to other materials, too.

Biocompatibility of printed paper-based arrays for 2-D cell cultures.

The use of paper-based test platforms in cell culture experiments is demonstrated. The arrays used for two-dimensional cell cultures were prepared by printing patterned structures on a paper substrate using a hydrophobic polydimethylsiloxane (PDMS) ink. The non-printed, PDMS-free areas formed the array for the cell growth experiments. Cell imaging was enabled by using a lipophilic staining agent. A set of coated paper substrates was prepared to study the effect of the physicochemical properties of the substrate (topography, roughness and surface energetics) on cell attachment and growth. The studied paper substrates were found to be cell-repellent or cell-supporting. Cell growth was supported by substrates with a large bearing area, low surface area ratio (Sdr), high total surface free energy and an intermediate electron donor surface energy component. The cells were grown to full confluency within 72 h.

Application of paper-supported printed gold electrodes for impedimetric immunosensor development.

In this article, we report on the formation and mode-of-operation of an affinity biosensor, where alternate layers of biotin/streptavidin/biotinylated-CRP-antigen/anti-CRP antibody are grown on printed gold electrodes on disposable paper-substrates. We have successfully demonstrated and detected the formation of consecutive layers of supra-molecular protein assembly using an electrical (impedimetric) technique. The formation process is also supplemented and verified using conventional surface plasmon resonance (SPR) measurements and surface sensitive characterization techniques, such as X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The article provides a possible biosensor development scheme, where-(1) fabrication of paper substrate (2) synthesis of gold nanoparticle inks (3) inkjet printing of gold electrodes on paper (4) formation of the biorecognition layers on the gold electrodes and (5) electrical (impedimetric) analysis of growth-all are coupled together to form a test-structure for a recyclable and inexpensive point-of-care diagnostic platform.

Versatile characterization of thiol-functionalized printed metal electrodes on flexible substrates for cheap diagnostic applications.

BACKGROUND: Cheap, reliable, point-of-care diagnostics is a necessity for the growing and aging population of the world. Paper substrate and printing method, combined together, are the cheapest possible method for generating high-volume diagnostic sensor platforms. Electrical transduction tools also minimize the cost and enhance the simplicity of the devices. METHODS: Standard surface characterization techniques, namely contact angle measurements, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) were used to analyze the growth of the organic thiol layers on top of the printed metal electrodes on paper substrates. The results were compared with those obtained by impedimetric electrical characterization method. RESULTS: This article reports the fabrication and characterization of printed metal electrodes and their functionalization by organic layers on paper and plastic substrates for biosensing and diagnostic applications. Impedimetric measurement is proposed as a simple, yet elegant, method of characterization of the organic layer growth. CONCLUSIONS: Very good correlation was observed between the results of organic layer growth from different measurement methods, justifying the use of paper as a substrate, printing as a method for fabricating metal and organic layers and impedance as a suitable measurement method for hand-held diagnostic devices. GENERAL SIGNIFICANCE: This result paves the way for the fabrication of more advanced bio-recognition layers for bio-affinity sensors using a printing technology that is compatible with flexible and cheap paper substrates. This article is part of a Special Issue entitled Organic Bioelectronics - Novel Applications in Biomedicine.

Inkjet-printed gold electrodes on paper: characterization and functionalization.

Gold nanoparticles were synthesized and inkjet-printed on a paper substrate and IR-sintered to produce conductive electrodes. The electrodes were further functionalised by using self-assembled octadecanethiol monolayers (SAMs). The effect of sintering, print quality, and SAM formation were examined by topographical, chemical and electrical methods. With optimised printing parameters, a volume resistivity of ~1.6 × 10(-7) Ω m was attained by a single print layer.

Inkjet printing of drug substances and use of porous substrates-towards individualized dosing.

Medicines are most often oral solid dosage forms made into tablets or capsules, and there is little room for individualized doses. The drug substance and additives are processed through multiple production phases, including complex powder handling steps. In drug manufacturing, the control of the solid-state properties of active pharmaceutical ingredient (API) is essential and it offers opportunities for enhancement of drug delivery systems. In this context, inkjet printing technologies have emerged over the last decades in pharmaceutical and biological applications and offer solutions for controlling material and product characteristics with high precision. Here we report the concept of conventional inkjet printing technology to produce printable pharmaceutical dosage forms on porous substrates. Data are shown to demonstrate inkjet printing of APIs into paper substrates, and how the model drug substances (paracetamol, theophylline, and caffeine) are penetrating the porous substrates used. The method enables controlling not only the deposition but also the crystallization of the drug substances. We anticipate that the inkjet printing approach has immense potential in making sophisticated drug delivery systems by use of porous substrates in the future. For example, it may offer new perspectives for solving problems around poorly soluble drugs and dosing low-dose medicines accurately. Furthermore, with the advent of genetic mapping of humans, controlled inkjet dosing can bring solutions to fabricate on-demand individualized medicines for patients.

Impact of surface defects and denaturation of capture surface proteins on nonspecific binding in immunoassays using antibody-coated polystyrene nanoparticle labels.

Microtiter wells are commonly used for bioassays. The sensitivity of such an assay depends on several instrumental and biochemical parameters such as the signal-to-background ratio and nonspecific binding of the label molecules. In this study, we have investigated the possible effects of well surface defects, well edges and denaturation of capture antibodies on the assay sensitivity. We used internally dyed Eu(III) chelate polystyrene nanoparticles as high specific activity labels in a thyroid stimulating hormone (TSH) sandwich-type model assay. The nanoparticle labels provide a high signal-to-background ratio in assays but the major limiting factor of the assay sensitivity is nonspecific binding of the labels. In our model assay the capture monoclonal antibodies were immobilized on microtiter wells passively or through streptavidin (SA)-biotin linkage. At first, commercially manufactured microtiter well surfaces were probed with an atomic force microscopy and significant structural inhomogeneities were found. The nonspecific binding of the nanoparticle conjugates did not appear to follow any of the microtiter well surface defect patterns in a number of experiments. In addition, the microtiter well edges did not increase the nonspecific binding. Denaturation of capture antibodies on solid surfaces has been proposed to expose amino acid sequences promoting nonspecific binding. This was studied by intentionally denaturing the surface capture antibodies by heat, detergent or acid treatment prior to the assay. Although specific signal was almost entirely lost no significant effect on nonspecific binding was observed. The passively adsorbed antibodies denatured at lower temperatures than those captured through streptavidin-biotin linkage. Evidently, the additional protein (SA) layer protected the capture antibody from denaturation whereas the solid surface appeared to act as a "catalyst" making the passively adsorbed antibody more susceptible to denaturation.